Amt emulator mac pdf guide install#
Amt emulator mac pdf guide serial#
Amt emulator mac pdf guide drivers#
Amt emulator mac pdf guide manual#
Amt emulator mac pdf guide software#

Amt emulator mac pdf guide manual#

Details can be found in the UserвЂ™s manual or programmers manual. Please note in PPLA emulation control codes such as precede many of the setup commands. You can now open this file with any text editor for an example of the label format and setup commands. When the printed label is what you want select the вЂњPrint to FileвЂќ option under File/Print and name the file descriptively with a. Now design a label closely matching your intended label in XBar. Make sure the emulation PPLA, PPLB, or PPLZ match what is loaded in your printer (see configuration report). Then make sure under File/Print/Select Printer, your model is selected.

Amt emulator mac pdf guide install#

After installing the included Windows drivers, install XBar.

The best way is to use the included XBar program. What is the best way to determine what commands need to be sent to the printer? I plan on programming my label format on my host computer. Using the save to file option under XBar is a good way to see the required programming strings. Also, if you are writing the program to send data to the printer, make sure the commands are included in your data stream. In this case the file can be used to configure multiple printers by using a DOS copy command. After making sure all options are set, either send the blank label to the printer by printing or save to a file using the save to file check box. If there is any question do a configuration print to determine installed emulation. The emulation is PPLA as shipped from the factory. All models are 200DPI except the FM403TT and FM4603. Also make sure the emulation and print head resolution are selected under File/Print/Select Printer option. Under options, un-check the Ribbon selection. This can be set from Xbar by selecting File/Print/Select Printer/Printer Setup. To do so the printer must be set up for direct thermal mode. Direct thermal media can be used in thermal transfer models. Changes to baud rate are stored in NVM.Д¬an I use thermal transfer models with direct thermal media? If so do I have to set anything on the printer?

Amt emulator mac pdf guide software#

Changing the baud rate is possible through software commands depending on emulation: PPLA- KI8n where n is, ,, 0,, 0. If in question use the factory reset method to reset the printer back to this condition.

Amt emulator mac pdf guide serial#

How do I change the serial port baud rate?ДЄs shipped from the factory the baud rate is set to 9600,8,1,N. The printer will then automatically perform a label calibration test. While powered up, press and hold the FEED button for around 10 seconds until the Ready and Power LEDвЂ™s turn off and then back on then release the feed button. My printer is acting up, how do I reset it to factory defaults?

Amt emulator mac pdf guide drivers#

If drivers from other sources are used make sure you match the driver to the emulation loaded in the printer as follows: PPLA use a Datamax type driver, PPLB use an Eltron type driver, PPLZ use a Zebra type driver. The supplied Windows drivers works with all versions of the printer regardless of the emulation loaded.

Which emulation needs to be loaded in my printer to use Windows drivers? Also ensure the media is loaded according to the users manual and you have performed a media calibration. How do I correct this?ДЇirst, if you have just loaded a new roll, make sure you shut the top cover before printing or feeding media. To exit this mode press the FEED key or cycle power on the printer.ДЄfter I load media, sometimes it does not feed properly and printing is in the wrong position. This allows all data sent to the printer to be displayed as HEX values which is useful debugging communication and programming issues. If the printer is loaded with PPLB emulation, вЂњHEX DumpвЂќ mode is automatically entered after running the configuration print out. Press the FEED key to exit this mode.ДЄfter performing the configuration print my printer prints in strange вЂњNumberвЂќ codes? How can I fix this? In PPLB emulation the printer will now be in a HEX dump mode. Continue to hold until feeding stops then release, after a pause the configuration report will print. How do I tell which emulation and firmware revision is loaded in my printer? Now each time the Feed key is pressed one form should feed. Load the media to be calibrated, power on the printer while holding the FEED key, release as soon as media starts feeding, then cycle power after the feed stops. changes) you must calibrate the media sensors. The first time you use Fastmark and each time a new type of media is loaded (length, gap, color, etc.

How/When/Why do I need to calibrate the media sensor?